● Configuring Your SoundBlaster in FreeBSD[Fwd - 荔园在线 | 深圳大学学生论坛,荔园晨风BBS,深大在线网站

荔园之美，在春之萌芽，在夏之绽放，在秋之收获，在冬之沉淀

发信人: zzt (我命由我不由天), 信区: Linux
标  题: Configuring Your SoundBlaster in FreeBSD[Fwd]
发信站: BBS 荔园晨风站 (Fri Sep  3 16:34:41 1999), 转信

【以下文字转载自 zzt 的信箱】
【原文由 zzt.bbs@bbs.zd.dhs.org 所发表】
作者: fuse (保险丝) 看板: FreeBSD
标题: Configuring Your SoundBlaster in FreeBSD
时间: Fri Jun  4 02:50:30 1999

Configuring Your SoundBlaster in FreeBSD

Sound card configuration under FreeBSD is not the most intuitive or well docume
nted procedure. Here's some info to help you along, and examples from my own, w
orking kernel. I've used the SoundBlaster AWE 32 and AWE 64 cards successfully.

This document will give you simple instructions for the traditional FreeBSD sou
nd driver configuration. If you want to configure your sound card using Luigi's
new PnP code, check out Luigi's Sound Drivers Also check out the file /usr/src
/sys/i386/isa/sound/sound.doc for more information.

Brief description of IRQ/DRQ settings:

In the following examples, note how the IRQ is set, and how the DRQ is used to
encode the DMA channel. This is crucial! Also note that cards such as some Grav
is UltraSound (GUS) cards use a 2nd DMA channel. This must be specified in the
flags!

SoundBlaster typical setup with one DMA channel:

# Sound blaster with IRQ 5 and DMA channel 1:
device sb0 at isa? port 0x220 irq 5 drq 1 vector sbintr

The case is much the same for this example GUS card:

# GUS using IRQ 12 and only one DMA channel (1):
device gus0 at isa? port 0x220 irq 12 drq 1 vector gusintr

Finally, an example GUS with two DMA channels. Note that the second DMA channel
is configured in the 'flags':

# GUS using IRQ 12 and two DMA channels, 1 and 3:
device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3 vector gusintr

1. Check the LINT file.

LINT is your ally. It contains examples for most types of hardware. My examples
will use SoundBlaster specific configs. If you have a different type of Sound
Card, or if your card does not work after using my examples, read the LINT file
for hints with your card. To get to the Sound Driver part of the LINT file, do
this:

a. cd /usr/src/sys/i386/conf/

If you do not have this directory, then you do not have your kernel sources. Ba
ck up a page and check for CVSUP information.

b. Read the file LINT, searching for the line:

# Audio drivers: `snd', `sb', `pas', `gus', `pca'

This is the first line of the Audio Drivers section.

2. Edit your kernel config file and add these options:

# Controls all sound devices
# snd: Voxware sound support code
controller      snd0
# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
device sb0      at isa? port 0x220 irq 5 drq 1 vector sbintr
# sbxvi: SoundBlaster 16
device sbxvi0   at isa? drq 5 conflicts
# sbmidi: SoundBlaster 16 MIDI interface
device sbmidi0  at isa? port 0x330
# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
device opl0     at isa? port 0x388

Note that if you are using a GUS card, you will have to experiment. Find the gu
s0 entries in LINT and use them. First you will need to determine whether your
GUS card has 1 or 2 DMA channels. Use the 'device gus0' line in place of the 'd
evice sb0' line. Remove the SoundBlaster options which you won't need.

3. Create the snd0 device.
# cd /dev
# ./MAKEDEV snd0

4. Remake your kernel and Reboot.
When you are done with this, you will need to remake your kernel, install the n
ew kernel and reboot your system.

5. Test your /dev/audio.
Grab this ftp://flag.blackened.net/incoming/sounds/sorrydave.au
Try to play it through /dev/audio:
# cat ./sorrydave.au > /dev/audio
Did you hear anything? Were your speakers on? Were your Port and IRQ/DRQ settin
gs correct? These things may need to be tweaked for your particular settings.

FreeBSD for the Lazy and Hopeless

--
※ Origin: 笑书亭 <bbs.zd.dhs.org>
◆ From: 210.32.151.168
--
※ 转载:．BBS 荔园晨风站 bbs.szu.edu.cn．[FROM: 192.168.1.144]

荔园在线首页友情链接：深圳大学深大招生荔园晨风BBS S-Term软件网络书店