荔园在线

荔园之美,在春之萌芽,在夏之绽放,在秋之收获,在冬之沉淀

[回到开始] [上一篇][下一篇]


发信人: georgehill (终生勤奋便成天才), 信区: Linux
标  题: 转载:How to Dual Boot Solaris[tm] and Linux[Forwa
发信站: BBS 荔园晨风站 (Thu Dec 30 17:43:57 1999), 转信

发信人: linuxrat (叫我老鼠错不了), 信区: Linux
标  题: How to Dual Boot Solaris[tm] and Linux[Forward]
发信站: BBS 水木清华站 (Thu Dec 30 13:43:24 1999)

 I got it from www.sun.com for someone's need. :) Hope SunGuys lucky.
 It's a little bit long, so be patient. :)
 Copyright(C) 2000 by Sun Microsystem. I haven't got permissions yet.
====================Begin posting by Linuxrat==============================
How to Dual Boot Solaris[tm] and Linux
   The following instructions discuss how to dual boot the Solaris(TM)
   operating environment in partition 0 and Linux in partition 8.

   If you are not a current Solaris user, please visit our Free
   Solaris(TM) program and try Solaris for noncommercial and educational
   use.

   1. Install UltraPenguin Linux (1.1.9 or later) or equivalent in the
   usual way (CD-ROM or net).
     * When the installer prompts for partitioning, allocate partition 8
       for Linux root and 7 for Linux swap. Allocate partition 1 for
       Solaris ("SunOS root") and partition 2 for "SunOS swap". You can
       also allocate other partitions as desired for Solaris or Linux
       use. The Linux installer calls the first partition 1, and has
       codes for the Solaris partitions. Partition 3 (or 4) should be the
       whole disk.
     * Make partition 8 the root partition, and install Linux there.
       Install Linux swap in partition 7.
     * Complete the Linux install as usual.
       IMPORTANT: Install the silo boot loader in the same prompt on the Ultra
systems.
     * Boot the system with Linux to check install. (startx will get the
       X windows up).
     * "halt" will sync the system and halt the OS (OK prompt).

   2. Install Solaris in the usual way (net or CD-ROM).

     * During the Solaris partitioning, the installer will ask if you
       want to preserve data. Click on "preserve data", then preserve all
       the partitions used for Linux.
     * Create one or more partitions for use with Solaris, and let
       Solaris format them. This is optional.
     * Install Solaris on partition 0 (first partition).
     * When the installer asks if you want to make the new root partition
       the default boot in NVRAM, say yes.
     * The installer will then complete the Solaris install as usual, and
       will reboot automatically to Solaris if you ask it to do that.

   3. At the OK prompt, type "show-disks" The disk paths will be printed.
   Type "devalias" to get the path format for the disk you are using.
     * Choose the correct hard disk path (only one for Ultra5)
     * Type "nvalias linux ^Y <disk_path_from_above>$0,0:h>"
     * If you wish, type
       "nvalias solaris ^Y <disk_path_from_above>@0,0:a"
     * Fix the printenv: "setenv boot-device disk:a".
       To change the default to Linux, substitute :h for :a.
     * Set autoboot on if you wish.

   4. "boot" or "boot solaris" or "boot disk"" boots Solaris from
   partition a. "boot linux" boots Linux from partition h.

   5. You can reinstall Linux or Solaris as many times as you want,
   without bothering the other installation.
====================End of post by Linuxrat===============     因为我爱自由!
|
|                      |                        |                    |
|   截拳道宗师-李小龙  |        意拳宗师-王芗斋 |     土人  Linuxrat |
|======================+========================+====================|

※ 来源:·BBS 水木清华站 smth.org·[FROM: 202.112.168.252]

--

     书山有路勤为径;
     学海无涯苦作舟!
 我是来自大富翁的小美!^_^

※ 来源:·BBS 荔园晨风站 bbs.szu.edu.cn·[FROM: 192.168.1.115]


[回到开始] [上一篇][下一篇]

荔园在线首页 友情链接:深圳大学 深大招生 荔园晨风BBS S-Term软件 网络书店