● NT4对硬盘的支持问题 - 荔园在线 | 深圳大学学生论坛,荔园晨风BBS,深大在线网站

荔园之美，在春之萌芽，在夏之绽放，在秋之收获，在冬之沉淀

发信人: tomsailor (last learn,last meal), 信区: WinNT
标  题: NT4对硬盘的支持问题
发信站: BBS 荔园晨风站 (Mon Sep 27 12:29:10 1999), 转信

DOCUMENT:Q197667
TITLE   :Installing Windows NT Server on a Large IDE hard drive
PRODUCT :Microsoft Windows NT
PROD/VER:4.00
OPER/SYS:WINDOWS

---------------------------------------------------------------------
The information in this article applies to:

- Microsoft Windows NT Server version 4.0
- Microsoft Windows NT Workstation version 4.0
- Microsoft Windows NT Server version 4.0, Terminal Server Edition
- Microsoft Small Business Server versions 4.0, 4.0a
---------------------------------------------------------------------

SYMPTOMS
========

During the installation of Windows NT to an 8 gigabyte (GB) or larger IDE
hard drive, the computer may stop responding (hang) during the format
portion of setup. If the drive was previously formatted as FAT and
designated to be converted to NTFS, the computer may hang during the
conversion process. Other symptoms include the drive taking an extremely
long time to format or Windows NT not recognizing the entire size of the
drive.

CAUSE
=====

The Microsoft supplied generic IDE driver (Atapi.sys) may not be fully
compatible with drives larger that 8 GB. This issue only affects IDE-based
drives 8 GB and larger.

RESOLUTION
==========

Windows NT 4.0 Service Pack 4 (SP4) has a new Atapi.sys file that allows
the drive to be formatted during setup of Windows NT. SP4's Atapi.sys can
also access space beyond 8 GB on these IDE drives.

NOTE: The system board BIOS must support and recognize drives larger than 8
GB before Windows NT can access the entire drive. You can verify this
ability by entering into the BIOS or contacting your system board
manufacturer.

If you are using Windows NT 4.0 Workstation, Server, or Terminal Server,
follow these instructions:

1.rvice Pack 4 IDE Driver."

2. Boot from the three setup disks supplied with Windows NT Server.

3. When asked if you would like setup to detect your mass storage devices,
   press S so that detection is skipped and you specify a mass storage
   device.

4. When setup list devices found, which should list <none>, press S again
   and insert the Microsoft ATAPI Service Pack 4 IDE Driver disk and press
   ENTER twice.

5. After setup reads the disk and list the Microsoft ATAPI Service Pack 4
   IDE driver, press ENTER to accept the driver.

6. Setup will now list Microsoft ATAPI Service Pack 4 IDE Driver as an
   installed driver. If you have additional drivers for other mass storage
   devices, press S; if not, press ENTER to continue through setup.

7. Setup should continue through normally but, it will prompt you to insert
   the disk labeled "Microsoft ATAPI Service Pack 4 IDE Driver Support
   Disk" at the copy phase after you have chosen or formatted a partition
   on a hard drive.

If you are using Microsoft Small Business Server 4.0 or 4.0a, follow these
instructions:

1. Download the updated ATAPI.SYS from Microsoft's FTP server

   ftp.microsoft.com/bussys/winnt/winnt-unsup-ed/fixes/nt40/atapi/ATAPI.EXE

   and copy the file to a blank floppy disk. Run all Business Server (SBS) disk
2. To do this,
   rename the file Winnt.sif to Winnt.bak on disk 2. Then copy the
   Winnt.sif from the I386 folder on SBS CD 1 to SBS disk 2.

3. Boot from the modified SBS setup disks. When the computer is booting off
   ofck screen and no visible indicators occur when you
   press F6.

4. When prompted, insert the modified disk 2 into the computer.

5. The next screen that appears will prompt you to specify a mass storage
   drivers. To do that, press the S key and then arrow down to the listing
   of OTHER. Insert the Microsoft ATAPI Service Pack 4 IDE Driver disk and
   press ENTER twice.

6. After setup reads the disk and list the Microsoft ATAPI Service Pack 4
   IDE driver, press ENTER to accept the driver.

7. Setup will now list "Microsoft ATAPI Service Pack 4 IDE Driver" as a
   installed driver. If you have any more drivers for other mass storage
   devices, press S; if not, press ENTER to continue through setup.

   NOTE: Because we are using a modified version of Winnt.sif, you will be
   prompted to insert disks 2 and 3 several times. Make sure you format or
   convert the partition to NTFS as SBS requires it.

8. Setup should continue through normally but it will prompt you to insert
   the disk labeled "Microsoft7
   TITLE     : STOP 0x0000000A or Difficulty Recognizing IDE CD-ROM Drives

   ARTICLE-ID: Q183654
   TITLE     : IBM DTTA-351010 10.1 GB Drive Capacity Is Inaccurate

Additional query words: 8gb 10gb
==================================================== MICROSOFT KNOWLEDGE BASE IS
PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.  MICROSOFT DISCLAIMS
ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  IN NO
EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF
MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.  SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES
SO THE FOREGOING LIMITATION MAY NOT APPLY.

--
※ 来源:．BBS 荔园晨风站 bbs.szu.edu.cn．[FROM: 192.168.1.193]

荔园在线首页友情链接：深圳大学深大招生荔园晨风BBS S-Term软件网络书店