荔园在线

荔园之美,在春之萌芽,在夏之绽放,在秋之收获,在冬之沉淀

[回到开始] [上一篇][下一篇]


发信人: Jobs (温少), 信区: WinNT
标  题: Chapter 5: Troubleshooting the Shared SCSI Bus
发信站: BBS 荔园晨风站 (Sun Nov 28 12:56:06 1999), 站内信件



Chapter 5: Troubleshooting the Shared SCSI Bus
Verifying Configuration
For the shared SCSI bus to work correctly, the SCSI host adapters must be
configured correctly. As with SCSI specifications, each device on the bus must
have a unique ID number. For proper operation, ensure that the host adapters
are each set to a unique ID. For best results, set one adapter to ID 6 and the
other adapter to ID 7 to ensure that the host adapters have adequate priority
on the bus. Also, make sure that both adapters have the same firmware revision
level. Because the shared SCSI bus is not used for booting the operating system,
 disable the BIOS on the adapter, unless otherwise directed by the hardware
vendor.

Make sure that you connect only physical disk or hardware RAID devices to the
shared bus. Devices other than these, such as tape drives, CD-ROM drives, or
removable media devices, should not be used on the shared bus. You may use them
on another bus for local storage.

Cables and termination are vital parts of the SCSI bus configuration, and
should not be compromised. Cables need to be of high quality and within SCSI
specifications. The total cable length on the shared SCSI bus needs to be
within specifications. Cables supplied with complete certified systems should
be correct for use with the shared SCSI bus. Check for bent pins on SCSI cable
connectors and devices, and ensure that each cable is attached firmly.

Correct termination is also important. Terminate the bus at both ends, and use
active terminators. Use of SCSI Y cables may allow disconnection of one of the
nodes from the shared bus without losing termination. If you have terminators
attached to each end of the bus, make sure that the controllers are not trying
to also terminate the bus.

Make sure that all devices connected to the bus are rated for the type of
controllers used. For example, do not attach differential SCSI devices to a
standard SCSI controller. Verify that the controllers can each identify every
disk device attached to the bus. Make sure that the configuration of each disk
device is correct. Some newer smart devices can automatically terminate the bus
or negotiate for SCSI IDs. If the controllers do not support this, configure
the drives manually. A mixture of smart devices with others that require manual
configuration can lead to problems in some configurations. For best results,
configure the devices manually.

Also, make sure that the SCSI controllers on the shared bus are configured
correctly and with the same parameters (other than SCSI ID). Data transfer rate
and other parameter differences between the two controllers may encourage
unpredictable behavior.

Adding Devices to the Shared SCSI Bus
To add disk devices to the shared SCSI bus, you must properly shut down all
equipment and both cluster nodes. This is necessary because the SCSI bus may be
disconnected while adding the device or devices. Attempting to add devices
while the cluster and devices are in use may induce failures or other serious
problems that may not be recoverable. Add the new device or devices in the same
way you add a device to a standard SCSI bus. This means you must choose a
unique SCSI ID for the new device, and ensure that the device configuration is
correct for the bus and termination scheme. Verify cable and termination before
applying power. Turn on one cluster node, and use Disk Administrator to assign
a drive letter and format each new device. Before turning on the other node,
create a physical disk resource using Cluster Administrator. After you create
the physical disk resource and verify that the resource will go online
successfully, turn on the other cluster node and allow it to join the cluster.
Allowing both nodes to be online without first creating a disk resource for the
new device can lead to file system corruption, as both nodes may have different
interpretations of disk structure.

Verifying Cables and Termination
A good procedure for verification of cable and termination integrity is to
first use the SCSI host adapter utilities to determine whether the adapter can
identify all disk devices on the bus. Perform this check with only one node
turned on. Then, turn off the computer and perform the same check on the other
system. If this initial check succeeds, the next step is to check drive
identification from the operating system level, with only one of the nodes
turned on. If MSCS is already installed, then the cluster service will need to
be started for shared drives to go online. Check to make sure the shared drives
go online. If the device fails, there may be a problem with the device, or
perhaps a cable or termination problem.

? 1999 Microsoft Corporation. All rights reserved. Terms of use.

--
☆ 来源:.BBS 荔园晨风站 bbs.szu.edu.cn.[FROM: bbs@192.168.11.73]


[回到开始] [上一篇][下一篇]

荔园在线首页 友情链接:深圳大学 深大招生 荔园晨风BBS S-Term软件 网络书店